To suit the PRO1247D HDTV over CAT5 distribution hub

Features:

• The PRO1247DS allows you to add more zones to your existing HDTV over CAT5 AV distribution set up
• Receives HD video and audio signals from the PRO1247D distribution hub from up to 120 metres
• Transmits IR signals to remotely control AV devices
• Power LED
  Receives power via CAT5 connection with hub
• Supports 480p / 1080i
• Can be wall mounted (screws included)

Connections:

• 2x RJ45 ports
• YPbPr video output (3x RCA)
• Coaxial digital audio (DA) output (1x RCA)
• Stereo audio (L / R) output (2x RCA)
• 1x IR receiver input (3.5mm jack)

Specifications:

• Video nominal input level: 1 Volt (peak to peak)
• Video output impedance: 75 ohm
• Audio output impedance: 300 ohm
• Power: 12V DC 1.2A switching power
• Weight: 310gr
• Dimensions: 158 (W) x 67 (D) x 31 (H) mm

Contents:

• HDTV over CAT5 receiver
• 4x screws for mounting
• Instructions

• Ability to add up to 4 speaker pairs to your amplifiers
• Left and right "commons" are isolated to work with alltypes of amplifiers
• Protection for amplifier and unit
• Small size to fit with any system
• No power required for operation
• Easy Installation
• Can handle up to 100 watts amplifier power with uniqueprotection circuitry

• Input: 100 Watts per channel max
• Outputs: 4 speaker pairs (4 to 16 ohmimpedance)
• Protection Circuit
  • Amplifier Protection: 3 Ω resistor per channel
  • Unit Protection: Automatic resetting poly switch
• Wire Gauge: 14 to 22 gauge
• Size: 298 (W) x 165 (D) x 50 (H) mm
• Weight: 1.3kg

• SPS4 selector
• User Manual
• Sheet of front panel labels
• Sheet of rear panel labels

• 1 input to 2 outputs
• Select Speaker Set A, B or A+B (please check for impedance compatibility with your amplifier when using A+B)
• Left (+/​-) & Right (+/​-) screw terminals for amplifier input
• Select output to speakers set 1, speaker set 2, or both sets at the same time
• 10 watts per channel
• 1 Speaker on, 2 Speakers on OR All Speakers on
• Designed with non-shorting selector switch so you can select between two speaker systems without overloading the output stages

• Audio power handling: 10 watts / channel continues music power
• Frequency response: 0.1 dB, from 20 Hz to 20kHz

PRO2 50W RMS x 2 WAY SPEAKER SELECTOR WITH VOLUME CONTROL

Controls two pairs of speakers. The SPS2A is fitted with separate volume controls, speaker on / off, and speaker protection on/​off switches.

The SPS2A allows independent volume control and on / off capability for up to two pairs of speakers. You choose where and how loud the music is in a particular location, without effecting the entire system. The speaker selection / volume control system is equipped with premium 10-step volume controls that maintain full 30dB dynamic range givingyou the maximum adjustment capability.

• 50 Watts RMS per channel
• High quality, durable metal cabinet
• Push-type speaker terminals x 12 (Amp L&R in, Speaker 1 L&R and Speaker 2 L&R out)
• Speaker 1 and Speaker 2 individual on/​off switches
• Speaker 1 and Speaker 2 individual volume control knobs
• Speaker protection (impedance correction) circuit with on/​off switch
• Playing 2 pairs of speakers (8ohms), set protection to out position
• Playing 2 pairs of speakers (4ohms), press in protection button

• Power handling: 50 Watts RMS per channel
• Attenuation (Volume): 10-position volume control
  • 1st position (fully counter clockwise): Volume off
  • 2nd and 3rd position: attenuate 6dB per step (6dB increase in vol)
  • 4th to 9th position: attenuate 3dB per step (3dBincrease in vol)
  • 10th position: Maximum volume
• Channel separation at 1 KHz: 38dB normal
• Cross talk between channels at 1 KHz: 50dB normal
• Speaker terminal wire size: 14-22 AWG
• Dimensions: 218 (W) x 150 (D) x 55 (H) mm

• Connect IR Repeater Kit (PRO1183) to up to eight IR Receivers via only 4 wires
• Light weight
• Screw terminals handle wire sizes form 24 to 12 gauge
• Wall mountable
• Small size and compact
• One-in eight-out
• Large detachable terminal block (supplied) for quickand easy installation in a structured wiring cabinet
• No power supply required; takes +12VDC power from IRRepeater Kit PRO1183 and distributes it to IR Receivers
• Design allows adding extra IR Repeater kits with minimal wiring (only IR and GND wires).
  • Do not connect +12V line to more than one IR Repeater to the IR Receiver Hub to avoid damage to IR Repeater

Specifications:

• Dimensions:196 (L) × 92 (W) × 30 (H) mm
• Weight: 198g

Lose the wires without compromising audio quality or having to upgrade your audio system!

Simply pair your Bluetooth enabled device–such as your smart phone, iPad, Android tablet–and connect theBMR3X to your AV receiver, multimedia speakers and more. With our inclusion of the highly renowned Apt-X codec, the BMR3X allows you to enjoy wireless Bluetooth audio quality indistinguishable from wired, with an impressive dynamic range. Apart from Apt-X, the BMR3X features a high-quality DAC that helps clean up poor audio that is often found in downloaded music and videos.

The BMR3X outputs audio though both analogue and digital outputs simultaneously! Notonly does this make it great for hooking up to your high-endamplifier or receiver using the high quality digital link, but you can also plug in another pair of powered speakers atthe same time! This allows you to listen through either system without the need to connect to another Bluetooth device!

A Signal-to-Noise Ratio (SNR) of more than 100dB, in combination with 2Vrms output at maximum volume means the BMR3X can not only compensate for low volume sources, but gives you a wider range of control from your mobile device without losing audio quality or increased background hiss you get from other devices on the market! Basically keep the volume on your amp or speakers low for reduced noise, and control the audio level directly from your phone or tablet—perfect for audiophiles!

• Apt-X codec
  for exceptionally high CD quality wireless performance
• Dual simultaneous output
  • S/​PDIF Optical output: For pure digital audio connection, ideal for connecting to AV Receivers
  • 3.5mm stereo output: For connection to any speakersystem, media player and more with a standard AUX input
• Auto-Pairing
  Once the BMR3X establishes a blueooth connection with a device, it will remember and auto-connect when that device is in range
• Multi-Device Support
  The BMR3X will remember and connect up to 8 devices
• Half the latency of other Bluetooth Receivers
  • only 70ms instead of the 180ms of other devices onthe market!
• Low SNR: >100dB
• Plenty of headroom for volume levels!
  • High level output: 2Vrms

• Audio bandwidth matching CD performance (16-bit, 44.1kHz)
• Low audio coding delay. Minimizes latency and ‘lip-sync’ issues
• Non destructive transcoding– no dueling effectswith other algorithms
• Backward Compatibility:
  when apt-X is not available target device will pair downto SBC
• Compression ratio of 4:1 and data rates up to 352kbps

Please note: Your source device must also have the apt-X codec. Please check your device user manual and specifications to be sure. If your device does not have apt-X, the BMR3X will still work, utilising the SBCcodec.

Some devices that have apt-X support include:

• HTC One S
• HTC One V
• HTC One X
• Motorola Droid Razr
• Samsung Galaxy S III (S3)
• Samsung Galaxy Tab 7.0 Plus
• Samsung Galaxy Tab 7.7
• Samsung Galaxy Note 10.1
• Apple Mac Mini (latest gen)
• Apple Mac book Air (latest gen)
• Apple Mac book Pro (latest gen) and more…

• BMR3X receiver
• 3.5mm plug to plug stereo lead
• 3.5mm socket to 2x RCA stereo lead
• 5V 0.6A DC power supply
• User manual